跪求单片机流水灯论文摘要英文翻译

Since the introduction of computer-chip technology in society, in every field in a wide range of applications.Running light control systems, the microcontroller is replaced by the gear regulating the delay time of old growth rate in future in the heart of this system.Due to the MCU has several benefits: small size, light weight, a single power supply; features, low power consumption and low; and the data transfer, one finds in SCM internal, run fast, uding, high reliability, so single-chip is widely used in measurement and control system, data acquisition, instrumental, Mechatronics product, smart interface, computer communications, as well as single-chip multilevel system, etc.This article is primarily deals with a subject name is single-chip-chip, flowing water and light control, which enables we learned how to use the SCM control our lives in the application of the facility.The design of this subject at a later time, introduced me to many aspects of the SCM.This topic describes in detail by the MCS-89C51 manifold programming the control circuit, it completed the single-chip flowing water and light control features, and gives specific hardware circuits and the appropriate program.This kind of control circuit reliability, flexibility, use the wide-ranging especially suitable for medium-sized cities of traffic lights, neon lights, etc.Rather, it on other similar system has certain significance.

流水灯带和rgb灯带区别

流水灯带和 RGB 灯带是两种不同类型的 LED 灯带。

流水灯带通常由一连串的 LED 灯构成，可以按照一定的顺序闪烁或者渐变，常用于装饰或者提醒。

RGB 灯带也是由 LED 灯构成的，不同的是它可以产生不同的颜色。通常由三色 LED 灯组成，分别为红、绿、蓝三色。通过控制三色 LED 灯的亮度，可以产生出许多不同的颜色。RGB 灯带常用于装饰或者提醒，也可用于照明。

总的来说，流水灯带和 RGB 灯带都是用来装饰或者提醒的灯具，但流水灯带只能产生一种颜色，而 RGB 灯带可以产生多种颜色。

流星灯带等于流水灯带嘛

不等于。

流水灯带是有控制器的，流星灯带，如为常规色温灯带，是不需要控制器的。

流水灯是若干个灯泡依次点亮，视觉上感觉到灯光在流动就叫做流水灯。其实道理蛮简单的。它是由无数个LED灯组成的，而LED就是发光二极管的简称，它有个特性：就是它只允许电流单一方向流过.。如果让LED灯亮起来，他需要连接一个高电平和一个低电平，当它遇到低电平时它会亮起来而遇到高电平它就会熄灭。由于他只能单方向流过电流，所以也就会一亮一暗。

宝马x3能刷流水转向灯吗?

可以，

改流水转向灯的想法自提车以来就有了，于是在网上买了一对水晶款LED流水灯带。但是测试的时候发现这种流水灯带的是三线制，红接电源、黄接转向、黑接电源地，红线有电源电压时白灯亮，黄线有转向电压时白灯灭、黄灯亮。理论上说只要红、黄并接转向信号，即可实现两线制接线，但测试结果是白灯闪亮后黄灯才亮，如此整个灯带的视觉效果就成了全部白灯瞬间闪亮后黄灯依次点亮直到全部亮起，而后在转向信号消失时全部熄灭，此后按照转向信号如此循环，没有了在黄灯全部点亮后再依次熄灭的过程。

考虑采取三线制接线的方案，即是增加一根电源线，只要断开INK1003的2脚即可。

最后一个问题就是原车转向灯的处理。之前已有车友发帖提到去除原车转向灯泡后车辆会报警，他的方案是把它放在一边，但这样会带来防水的问题。因此我的方案是原车转向灯座不动，转向信号线从转向灯插头处取针压接，原车转向灯泡用水泥电阻替代或者用黑色密封胶封涂遮光。